CCNA 2 SRWE – Switching, Routing, and Wireless Essentials (Version 7.00) – Modules 14 – 16 – Routing Concepts and Configuration test Answers

Refer to the exhibit. What will certainly the router execute with a packet that has actually a destination IP address of 192.168.12.227?


*
*
*
*
*
*
CCNA 2 SRWE v7 Modules 14 – 16 – Routing Concepts and also Configuration exam Answers 12


Create a static route pointing to Fa0/0 with an advertisement of 1.Create a static course pointing come 10.1.1.1 v an advertisement of 1.Create a static course pointing come 10.1.1.1 v an ad of 95.Create a fully specified static route pointing to Fa0/0 with an ad of 1.Create a fully specified static path pointing to Fa0/0 with an ad of 95.

You are watching: Identifies the exit interface used to route a packet to a destination

Answers Explanation & Hints:

A floating static path is a static path with an governmental distance greater than the of one more route already in the routing table. If the path in the table disappears, the floating static course will be put right into the routing table in that place. Interior EIGRP has an ad of 90, so a floating static path in this script would require to have an AD greater than 90. Also, when creating a static course to a multiaccess interface like a FastEthernet segment a completely specified route have to be used, through both a next-hop IP address and an departure interface. This prevents the router native doing a recursive lookup, yet still guarantee the correct next-hop device on the multiaccess segment forwards the packet.

What is a properties of a floating revolution route?

It is supplied to provide load balancing between static routes.When the is configured, it creates a gateway of last resort.​It is configured with a higher administrative distance 보다 the initial dynamic routing protocol has.It is merely a static path with 0.0.0.0/0 as the location IPv4 address.
Answers Explanation & Hints:

Floating static paths are revolution routes supplied to administer a back-up path to a primary static or dynamic route, in the event of a connect failure. They must be configured v a higher administrative distance than the original dynamic routing protocol has. A default static route is just a static course with 0.0.0.0/0 together the destination IPv4 address. Configuring a default static route creates a gateway of last resort.

What network prefix and also prefix-length mix is used to develop a default static course that will certainly match any kind of IPv6 destination?

::/128::/0::1/64FFFF::/128
Answers Explanation & Hints:

A default static route configured for IPv6, is a network prefix of all zeros and a prefix mask of 0 i beg your pardon is expressed as ::/0.

Consider the adhering to command:

ip path 192.168.10.0 255.255.255.0 10.10.10.2 5

Which route would need to go down in order for this static route to appear in the routing table?

a default routea static path to the 192.168.10.0/24 networkan OSPF-learned course to the 192.168.10.0/24 networkan EIGRP-learned route to the 192.168.10.0/24 network
Answers Explanation & Hints:

The bureaucratic distance of 5 added to the finish of the static route creates a floating static situation for a static course that walk down. Static routes have a default administrative distance of 1. This route that has an governmental distance of 5 will certainly not be put into the routing table uneven the previously gone into static path to the 192.168.10.0/24 goes down or was never entered. The administrative distance that 5 added to the finish of the static course configuration create a floating static course that will be placed in the routing table as soon as the major route to the same destination network go down. Through default, a static route to the 192.168.10.0/24 network has an bureaucratic distance of 1. Therefore, the floating course with an bureaucratic distance the 5 will certainly not be placed into the routing table unless the previously gotten in static route to the 192.168.10.0/24 goes under or was never entered. Because the floating route has actually an governmental distance that 5, the path is preferred to an OSPF-learned route (with the administrative distance that 110) or an EIGRP-learned route (with the bureaucratic distance the 110) come the same destination network.

Consider the adhering to command:

ip course 192.168.10.0 255.255.255.0 10.10.10.2 5

What walk the 5 in ~ the finish of the command signify?

metricexit interfaceadministrative distancemaximum variety of hops come the 192.168.10.0/24 network
Answers Explanation & Hints:

The 5 in ~ the finish of the command signifies administrative distance. This worth is added to floating static courses or routes that only appear in the routing table when the preferred route has gone down. The 5 at the finish of the command signifies administrative distance configured for the static route. This value suggests that the floating static route will appear in the routing table once the wanted route (with an administrative distance much less than 5) is down.

Consider the adhering to command:

ip course 192.168.10.0 255.255.255.0 10.10.10.2 5

How would an administrator check this configuration?

Delete the default gateway path on the router.Ping any type of valid deal with on the 192.168.10.0/24 network.Manually shut under the router user interface used together a major route.Ping native the 192.168.10.0 network come the 10.10.10.2 address.
Answers Explanation & Hints:

When a static course is configured v the following hop deal with (as in the instance of the 192.168.10.128 network), the calculation of the display ip route command perform the route as “via” a details IP address. The router has to look up the IP address to identify which user interface to send the packet out. Due to the fact that the IP deal with of 10.0.0.6 is part of network 10.0.0.4, the router sends out the packet out user interface Serial0/0/1.

See more: 10% Of 700 ? Calculate 10% Of 700 What Is 10 Percent Off 700 Dollars Or Pounds

An administrator concerns the ipv6 route 2001:db8:acad:1::/32 gigabitethernet0/0 2001:db8:acad:6::1 100 command on a router. What bureaucratic distance is assigned come this route?

0132100
Answers Explanation & Hints:

The command ipv6 course 2001:db8:acad:1::/32 gigabitethernet0/0 2001:db8:acad:6::1 100 will configure a floating static course on a router. The 100 in ~ the finish of the command specifies the governmental distance the 100 come be used to the route.

Refer come the exhibit. What two regulates will readjust the next-hop address for the 10.0.0.0/8 network native 172.16.40.2 come 192.168.1.2? (Choose two.)