A countershaft transferring two V-belt pulleys is displayed in the figure. Pulley-block A receives strength from a motor with a belt v the belt emphasize shown. The strength is sent with the shaft and delivered to the belt on sheave B. I think the belt tension on the loose side at B is 15 percent of the anxiety on the chop side.

You are watching: A countershaft carrying two v-belt pulleys is shown in the figure

(a) identify the tensions in the belt on pulley-block B, suspect the shaft is running at a consistent speed.(b) discover the magnitudes that the bearing reaction forces, assuming the bearings act as straightforward supports.(c) draw shear-force and bending-moment diagrams for the shaft. If needed, make one set for the horizontal airplane and another set for the upright plane.(d) at the allude of preferably bending moment, identify the bending stress and also the torsional shear stress.

(e) in ~ the allude of preferably bending moment, determine the primary stresses and the maximum shearstress.

A
countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the... See Answer
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the... Check out Answer
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the... See Answer
A PMOS transistor based single-stage amplifier is shown in the figure below (Fig. Q2). The PMOS has = -0.7 V and a very large |VA|. Vi.p +2.5 V RS Cs Rsig HH Vsig RD -2.5 V Fig. Q2 What is the construction of the single-stage amplifier? What is the major application of this type of single-stage... View Answer
Draw the shear and moment diagrams for the shaft if the is subjected to the vertical loadings. The bearings at A and B exert only vertical reaction on the shaft. view Answer
arrange the following elements in stimulate of raising electronegativity: carbon , fluorine , oxygen , nitrogen see Answer
Selected financial statement data for ideal Buy Co., Inc., The Kroger Co .. Nordstrom, Inc., Office...... A.... (PPET) for each company. Discuss any kind of difference the you observe. C. Compute the gross benefit margin (GPM) for each company. How does the GPM differ throughout companies? does this difference... Watch Answer
Tobias is a 50% companion in Solomon LLC, i beg your pardon does not invest in genuine estate. On January 1, 2015, Tobias"s readjusted basis for his LLC attention is \$130,000, and his at-risk amount is \$105,000. His re-superstructure of accident from Solomon for 2015 is \$150,000, all of i m sorry is passive. He has actually another investment... Watch Answer
1. Create a course named Employee and create fields to save the complying with information. Employee id Employee surname Department Designation salary i. Ii. Iii. Iv. V. A. Write constructor for the class. b. create mutator and accesor methods for every fields. C. Develop two objects for the course Employee. D.... Watch Answer
to compare balance sheets for 2021 and 2020, a statement of revenue for 2021, and extr information from the accounting records of Red, Inc., are noted below. Extr information from the accountancy records:a. Throughout 2021, \$230 million of tools was to buy to change \$180 million... View Answer
think about two shafts in torsion, every of the exact same material, length, and cross-sectional area. One...... a heavy square cross section and the other shaft has actually a hard circular section.(a) i m sorry shaft has the better maximum shear stress and by what percentage?(b) which shaft has actually the greater angular... View Answer
A equipment reduction unit offers the countershaft shown in the figure.

See more: The Three Basic Control Methods Are ____., The Control Process

gear A receives power from another gear with the transmitted force FA used at the 20_ pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted pressure FB at the pressure... Watch Answer